working CHIP sender

1 files changed, 0 insertions, 93 deletions

diff --git a/trasmitter/sender.ino b/trasmitter/sender.ino
deleted file mode 100644
index 9373875..0000000
--- a/trasmitter/sender.ino
+++ /dev/null
@@ -1,93 +0,0 @@
-const uint16_t pulseScale = 520; // usec per sample unit
-
-// alternate HIGH and LOW, first one of each array is HIGH
-const uint8_t prologue[] = {
-  1,1, 1,1, 1,1, 1,1, 1,1, 1,1,
-  2,3, 1,1, 2,2, 1,1, 1,1, 2,1,
-  1,1, 1,1, 1,2, 1,1, 1,1, 1,1,
-  1,1, 1,1,
-};
-const size_t prologueSize = sizeof(prologue) / sizeof(uint8_t);
-
-const uint8_t epilogue[] = {
-  1,2, 2,2, 1,3, // the last value doesn't much matter
-};
-const size_t epilogueSize = sizeof(epilogue) / sizeof(uint8_t);
-
-const uint8_t onSignal[] = {
-  2,2, 1,1, 1,1, 1,1, 1,1, 2,1, 1,1,
-};
-const size_t onSize = sizeof(onSignal) / sizeof(uint8_t);
-
-const uint8_t offSignal[] = {
-  1,1, 1,1, 1,1, 1,1, 1,1, 2,2, 2,1,
-};
-const size_t offSize = sizeof(offSignal) / sizeof(uint8_t);
-
-const int nTxPin = 7; // Arduino digital pin you're using for radio data.
-
-void transmitArray(const uint8_t pulses[], size_t pulseCount) {
-  for(size_t idx = 0; idx < pulseCount; idx+=2) {
-    digitalWrite(nTxPin, HIGH);
-    delayMicroseconds(pulseScale*pulses[idx]);
-
-    digitalWrite(nTxPin, LOW);
-    delayMicroseconds(pulseScale*pulses[idx+1]);
-  }
-}
-
-void transmitSignal(const uint8_t signal[], size_t signalSize) {
-  transmitArray(prologue,prologueSize);
-  transmitArray(signal,signalSize);
-  transmitArray(epilogue,epilogueSize);
-}
-
-void sendTrain(const uint8_t signal[], size_t signalSize) {
-  transmitSignal(signal,signalSize);
-  delay(1000);
-  transmitSignal(signal,signalSize);
-  delay(2000);
-  transmitSignal(signal,signalSize);
-}
-
-
-/**
- * The setup() function is called when a sketch starts. Used  to initialize
- * variables, pin modes, start using libraries, etc. The setup function will
- * only run once, after each powerup or reset of the Arduino board.
- */
-void setup()
-{
-  pinMode(nTxPin, OUTPUT);
-  digitalWrite(nTxPin, LOW);
-  
-  Serial.begin(9600);
-  Serial.println("Press 0 to turn off heating");
-  Serial.println("Press 1 to turn on heating");
-
-}
-
-
-/**
- * The loop() function loops consecutively, allowing the program to change and
- * respond. Used to actively control the Arduino board.
- */
-void loop()
-{
-  if (Serial.available() > 0)
-  {
-    int nIncomming = Serial.read();
-    if (nIncomming == 49) { // char code for 1
-      Serial.println("ON");
-      sendTrain(onSignal,onSize);
-    }
-
-    if (nIncomming == 48) { // char code for 0
-      Serial.println("OFF");
-      sendTrain(offSignal,offSize);
-    }
-
-    Serial.println("Press 0 to turn off heating");
-    Serial.println("Press 1 to turn on heating");
- }
-}
\ No newline at end of file